自动上料搅拌车使用前各种阀门的制作

 来源:http://www.jufengjiaobanji.com 日期:2021-05-19 发布人:admin
1、检查各个水箱是否缺水并加足水,轮胎气压是否符合2.5bar以_上要求。
1. Check whether each water tank is short of water and full of water, and whether the tire pressure meets the requirement of 2.5bar_ I'm not sure.
2、检查发动机机油油尺,液压油箱标尺,齿轮箱油标观察孔,前、后桥,轮边减速轴头拧开油面油堵检查齿轮油是否符合要求,缺少应及时添加,总泵自动液油杯液面是否合乎标准要求。
2. Check the engine oil dipstick, hydraulic oil tank ruler, gearbox oil level observation hole, front and rear axle, wheel side reducer shaft head, screw off the oil level oil plug, check whether the gear oil meets the requirements, if it is missing, add it in time, and whether the automatic oil cup level of master cylinder meets the standard requirements.
3、观测发动机机油,齿轮油,检查油标尺,油标锣孔,液压油箱时,车辆要水平位置。
3. Observe the engine oil, gear oil, check the oil dipstick, oil mark, Gong hole, hydraulic oil tank, the vehicle should be in a horizontal position.
4、全车各部油管路,气管路接头是松动有无漏油,漏气现象。检查全车线路有无接触不良,各仪表,灯光是否工作正常。
4. The oil pipes and gas pipe joints of all parts of the car are loose, whether there is oil leakage or air leakage. Check if there is poor contact in the whole vehicle line, and if all instruments and lights work normally.
5、行驶前刹车是否制动有效,检查各操纵阀作用是否良好。
5. Check whether the brake is effective before driving, and check whether each control valve works well.
全自动自上料搅拌车
各操作阀的作用
Function of each operating valve
1、主车前后行走操纵阀( 快慢档,前进和倒车档)-般行走时为前驾,施工作业时为后驾。
1. The front and rear travel control valve (fast and slow, forward and reverse gears) of the main vehicle is generally the front drive when walking, and the rear drive when working.
2、大臂升降旋转操纵阀,举料,左右旋转罐体控制。
2. Boom lifting rotary control valve, lifting, left and right rotary can body control.
3、料斗上下料操纵阀,铲料、卸料控制铲斗作用。
3. Hopper loading and unloading control valve, shovel, discharge control bucket function.
4、手动油门操纵阀,控制发动机的转速,使搅罐在一定的平稳速度下旋转。
4. The manual throttle control valve controls the speed of the engine to make the stirring tank rotate at a certain steady speed.
5、座椅脚踏定位卡销,用于座椅调转方向时起到锁止作用,踏板踩向下时。锁销打开,左翼转到位置后制动锁止。
5. The foot positioning pin of the seat is used to lock the seat when the seat rotates, and when the pedal is depressed. When the lock pin is opened and the left wing is turned to the position, the brake is locked.
今天的全自动自上料搅拌车精彩内容就给大家分享到这了,更多的精彩内容请点击我们的网站http://www.jufengjiaobanji.com进行关注留言,后续会有更多的精彩内容为您呈现.
Today's automatic self feeding mixer wonderful content to share with you, more wonderful content please click on our website http://www.jufengjiaobanji.com Follow the message, there will be more wonderful content for you