避免自动上料搅拌机中卡纸需要怎么操作?

 来源:http://www.jufengjiaobanji.com 日期:2021-07-20 发布人:admin
不合理的卸货时间参数
Unreasonable unloading time parameters
由于自动上料搅拌机无法在料仓中安装水平仪,因此该行业基本上具有时间控制功能。如何设置时间参数,加载和卸载时间设置实际上非常简单。使用时,请设置较短的时间,然后根据每个抽吸位置缓慢添加。当物料水平达到吸入口时间时,可以减去一秒钟。排出时间是为了确保再次排出物料。这具有两个优点:首先,材料水平太高,并且对滤芯的损坏特别大。因此,我们的一些客户可以使用过滤器两年半。
Since the automatic feeding mixer can not be installed in the silo level, so the industry basically has the function of time control. How to set the time parameters, load and unload time settings are actually very simple. When using, please set a short time, and then add slowly according to each suction position. When the material level reaches the suction time, one second can be subtracted. The discharge time is to ensure that the material is discharged again. This has two advantages: first, the material level is too high, and the damage to the filter element is particularly large. As a result, some of our customers can use the filter for two and a half years.
其次,每次清洁材料时,截止阀都不会在关闭时关闭。频繁操作的密封阀将不会切换五到六次,这是特别危险的。
自动上料混凝土搅拌车
Second, each time the material is cleaned, the stop valve will not close when it is closed. Frequently operated seal valves will not switch five to six times, which is particularly dangerous.
我们的许多项目都使用手动枪来捡拾材料。为了便于将物料枪直接插入物料管或吨袋中,物料枪的吸入口被紧密的物料压缩,强大的负压将整个物料拉开。装载机的破坏力非常强,很容易堵塞管道。正确的方法是,物料在吸入口和空气之间形成一定的气液混合比,并在气流的推动下均匀地流入进料器。如果物料积压太长,则可能非常困难。此时,在喷枪上需要一个振荡器来破坏冷凝的材料。
Many of our projects use hand guns to pick up materials. In order to insert the material gun directly into the material pipe or the ton bag, the suction port of the material gun is compressed by the tight material, and the whole material is pulled apart by the strong negative pressure. The destructive power of the loader is very strong, and it is easy to block the pipeline. The correct way is that the material forms a certain gas-liquid mixing ratio between the suction port and the air, and flows into the feeder evenly under the push of the air flow. If the material backlog is too long, it can be very difficult. At this time, an oscillator is needed on the spray gun to destroy the condensed material.
在自动上料搅拌机的实际操作中,不可避免地会发生某些故障。阻隔材料更严重。因此,希望在理解了上述自动上料搅拌机的避免方法后,能够正确,合理地操作设备。
In the actual operation of the automatic feeding mixer, some failures will inevitably occur. The barrier material is more serious. Therefore, I hope that after understanding the above methods of automatic feeding mixer, I can operate the equipment correctly and reasonably.
不要超载。始终注意工作条件。环境温度高于25摄氏度,装载,运输和卸载时间不应超过60分钟。环境温度低于25摄氏度,上述时间不应超过90分钟。液压系统的压力符合使用说明书,不能随意调节。液压油的质量和数量必须符合原始要求。
Don't overload. Always pay attention to working conditions. When the ambient temperature is higher than 25 ℃, the loading, transportation and unloading time shall not exceed 60 minutes. If the ambient temperature is lower than 25 ℃, the above time shall not exceed 90 minutes. The pressure of the hydraulic system is in accordance with the operation manual and cannot be adjusted at will. The quality and quantity of hydraulic oil must meet the original requirements.
在施工现场卸货后自动使用连接到搅拌机的软管清洁漏斗,排水漏斗,排水斜槽等,以清除附着在车身上的污泥和混凝土。 在返回搅拌站的途中,将150-200升水倒入搅拌罐中,以清除残留在搅拌罐壁和叶片上的所有混凝土。
After unloading at the construction site, the hose connected to the mixer is automatically used to clean the funnel, drainage funnel, drainage chute, etc. to remove the sludge and concrete attached to the vehicle body. On the way back to the mixing plant, pour 150-200 liters of water into the mixing tank to remove all concrete remaining on the tank walls and blades.